Newest Servo from KoPropo!

This is Ko Propos hi-end brushless servo, brushless motor with hi-quality gear material - that same as RSx series.
The gears are made with a special Japanese aluminum. This gear is 45% lighter than brass and has the same hardness as steel.
Double ball bearing
Aluminum middle case
The middle case is machined from one piece of aluminum that incorporates the gear pins and motor being held properly in place.
Brushless motor

Item Number: KO30200

The EX-1 open perfectly new possibilities and set new standards by individuality and performance.

Now available!

Item KO80500

Actually the publication was sheduled to the toy fair Nuremberg, but the Internet was again faster. Because of this reason there is also still no price information and also no exact date for delivery. But probably the EX-1 will be available in the first half of the year.

Some more Details:

Joystick	Plug & Play	Connection Socket
On/Off Switch & Charging Jack	Battery Tray	USB - Interface

EX-1 picture gallery:

New from EDS!

The all new EDS Combo Caddy Set! Saves up to 6 Tools inside the handle.

7 Bits inclusive:

1,5mm; 2,0mm; 2,5mm; 3,0mm; 3,5mm Flathead; 3,0mm und 4,5mm Phillips.

Item: EDS-520101

Optional Parts:

EDS-520004 CADDY Adapter H6.35) for 1/4" Bits
EDS-521115 Hex 1.5 X 75mm
EDS-521120 Hex 2.0 X 75mm
EDS-521125 Hex 2.5 X 75mm
EDS-521130 Hex 3.0 X 75mm
EDS-522120 Ball Hex 2.0 X 75mm
EDS-522125 Ball Hex 2.5 X 75mm
EDS-522130 Ball Hex 3.0 X 75mm
EDS-523135 Flathead 3.5 X 75mm
EDS-524135 PHILLIPS 3.0 X 75mm
EDS-524145 PHILLIPS 4.5 X 75mm
EDS-525155 Nut Driver 5.5 X 75mm
EDS-525170 Nut Driver 7.0 X 75mm

Chung Yang Engines of the latest Generation are now available in 23cm³, 26cm³ and 27cm³.
Several parts get updated for a better performance and more life time. For example the Cylinder is now mounted with 4 instead of 2 bolts also the valve timing, crank case and piston is updated to get more power by a better fuel concept. The Walbro 668 carburetors are extreme reliable und guaranty a maximum performance. The clutch is factory based already lightened and in combination with the red clutch spring working on the best RPM.

• Cylinder with 4- bolts
• Reinforced crank case
• Rubber sealing for the stop switch
• New designed pistons
• New lightened clutch shoes
• Firm clutch spring
• Walbro WT-668 carburetor
• Exhaust
• Torx screws
• Choke for easy starting
• Robust pull-starter with integrated catch-dustcover

Item No.:
CYF270 - CY F270 Engine 27ccm 4-Bolt
CYF270M - CY F270 Engine27ccm 4-Bolt MCD version (as CYF270 but for MCD cars V4 Series)

CYF260 - CY F260 Engine 26ccm 4-Bolt
CYF260M - CY F260 Engine 26ccm 4-Bolt MCD version (as CYF270 but for MCD cars V4 Series)

CYF230 - CY F230 Engine 23ccm 4-Bolt

Item Pictures:

New lightened Clutch shoes, firm clutch spring

Walbro WT-668 Carburetor

Engine without (left) and with (right) MCD preparation

Officially licensed Walker Evans Racing wheels are molded from a blend of high quality nylon materials for strength and durability with a solid 12mm hex mount and dressed in black and chrome for eye catching looks.
 
• Officially licensed Walker Evans Racing replica wheels.
• Black wheels with chrome outer lip.
• Fits standard 1.9 tires.

Item: AX08140

Looking for the perfect solid axle kit for your next custom crawler, rock racer or tough truck? Look no further as Axial has released the AR60 OCP-Axle™ kit. Each kit includes everything needed to build one complete AR60 front axle. Add a second axle for a custom build with 4 wheel steering.

• AR60 axle housings are constructed from high strength composite material which has a low flex rate but is not as brittle as standard glass filled nylon.
• Axle tubes are reinforced and beefed up with a boxed-in axle truss to distribute stress over a larger area.
• Offset pumpkin provides more ground clearance and a better driveshaft angle.
• The ring and pinion gears are easily serviced by removing four screws to gain access for rebuilding, upgrading and performance tuning.
• Standard dog bones and outdrives included.
• Servo plate included.
• All hardware and drive pins included.
• Assembly required.

Item: AX30831

AX30793 Dig Component Set
Axial’s dig transmission case is easily upgradable for dig (patent pending) function which, when installed, gives you a three function transmission. The transmission also includes all steel outputs. The optional Dig Upgrade Set comes with servo linkage, slider parts and a new output shaft.
When installed you have 4x4, 4x2 (freewheel) and Dig (rear locked). This aids in extreme climbs, descents and tight technical turns.
 

• Compatible with Axial’s dig transmission case.
• All hardware included for easy bolt on application.
• Sintered steel working internals.
• Hardened steel main slider shaft.
• Servo not included.

Item: AX30793

Please note: You need a 3 Ch Radiosystem, optimal is the Ko Propo EX5-UR (Art. Nr.: KO80097)

The Powerswitch was designed for replacing the mechanical switch to supply the receiver and servos in nitro cars.
The switch is used to switch the receiver supply on and off inside the car.
Beside that the Powerswitch informs you about the remaining capacity and error conditions of your battery.
Caution: The Powerswitch is only a Switch. That means the connected voltage on the input is directly forwarded to the output when switched on.
For example, if you use a 7.4V LiPo battery you have to make sure that your receiver and your servos are able to handle this high voltage!
Load capacity: Because of newest MosFET technology the Powerswitch is despite it‘s small size capable of handeling large currents. The use in big scale cars with up to 3 servos is no problem.
Current consumption:
As a result of the extremly low current consumption the Powerswitch can be connected longer time to the receiver battery without discharging it too much. As an example: A fully charged 1600mAh battery would last about 950 days.


Features
• Rugged and reliable electrical switch for receiver supply in nitro cars
• Completly sealed against dust and water
• Programmable for 2S LiPo, 2S LiFe and 5 cells NiMH batteries
• Exact charge level indicator with 3 LEDs
• Error detection bad contact/bad battery
• Very low internal resistance for minimal losses
• Extremly low current draw when switched off
• Very high load capacity

Item: R01612

Sample of use:

All Servos and Spareparts available!

New Type of Servo arm: Just clamp the horn in the position you like (360°) and fix it with a Setscrew. For 25T Servos.

Blue HIG0001	Red HIG0002

The Servos fits perfect into: 1/10 Buggy, Truck, Monster, TW Scale and 1/8 Buggy, Truggy, Monster; The Heli Line fits into big Helikopters.

Overview:

Car Servos:

Helikopter Servos:

Helikopter Tailrotor:

Item: HG800 Voltage: 4,8 V - 6,0 V Torque (7.4V): 6,40 kgcm Torque (6.0V): 5,20 kgcm Speed (7.4V): 0.04 s/60° Speed (6.0V): 0.05 s/60° Elektronic: Digital Case: Alu - Middlecase Ballbearings: 2 Gears: Metall Motor: Coreless Weight: 62.0g Dimensions: 39.5x20.0x38.7 mm Horn Gear: 25 T Gears: HIG0104 Body: HIG0202
Item: HG900 Voltage: 4,8 V - 6,0 V Torque (7.4V): 6,40 kgcm Torque (6.0V): 5,20 kgcm Speed (7.4V): 0.04 s/60° Speed (6.0V): 0.05 s/60° Elektronic: Digital Case: Alu Ballbearings: 2 Gears: Metall Motor: Coreless Weight: 71.8g Dimensions: 39.5x20.0x38.7 mm Horn Gear: 25 T Gears: HIG0104 Body: HIG0203

Robitronic’s all new CUBE BL Modified Competition raises the bar for highly competitive brushless racing classes, boasting unprecedented throttle and brake control together with great current handling capabilities in a small sized package.
The CUBE’s impressive specs stem from it’s state-of-the-art power mosfets on a cutting edge pcb-design that takes its power handling straight up to what is technically feasible, driving even the hottest motors with minimal effort. A high-flow fan on top of the CUBE’s heat sink only kicks in when needed, keeping temperatures low till the final second of every heat.
Additionally, a specially developed boot loader lets the user update the CUBE’s firmware on his own, and the 6 integrated LEDs make the setup process a breeze!

Highlight Features
• The most current PowerFET technology provides the lowest internal resistance possible.
• The Cube’s special pcb-design ensures that there is the maximum amount of copper available to where it’s needed.
• 10 optimized power-profiles: formulated and proven by world class drivers.
• Sensitively adjustable auto-brake
• Turn off the Cube with your transmitter from the drivers’ stand if needed.
• External setup button with a pc-interface plug.
• Self-updating firmware thanks to an integrated boot loader
• Temperature-controlled high-flow fan.
• Optimized cooling fins keep the Cube cool.
• A big powercap provides maximum punch.

Software Update:

-Reverse mode (new)

- Autoroll (new)

- Undervoltage protection

- Autobrake

- 0 Boost (Timing 0) (LED blinks)

Technical Data:

Item Nr: R01220